Programmable Quinder 48V Brushless BLDC Controller
This BLDC controller offers extensive control options for the 48V 550W Quinder brushless hub motor.
Versions
This controller can be delivered in 2 different versions
10301059 Programmable 2023/2024 brushless DC Controller
10301063 Limited Programmable 2025 closed-loop DC Controller with HIGO connectors
10301059 Programmable 2023/2024 brushless DC Controller
This 48Volt brushless DC Controller can be used with the Quinder 48V HUB motor. The controllers offers several programming possebilities. The controller can be plug-and-play connected to Display throttle or POT-meter throttle, FWD/REV, the HUB motor and a speaker for warning signals.
10301063 Limited Programmable 2025 closed-loop DC Controller with HIGO connectors
This 48Volt brushless controller can also be used with the 48V Quinder HUB motor. The controller has 3 Higo connectors; 1 for the 48V HUB motor, 1 for the DX124 throttle with Higo and 1 for the fwd/rev with Higo. The only programming possebility is to activate or de-activate the e-brake. The controller has 1 connection for the speaker and 1 for switching tyhe driving mode of the wheel. depending on connected or disconnected. The closed-loop controller has three speeds preprogrammed when used with the DX124 display throttle, Eco; 0-2kmh, Mid 0-4kmh, High 0-6kmh. These speeds are set for LvS spraying applications
Programming Options for 10301059
The following settings can be adjusted via an interface:
- Acceleration Mode: Hard start / Soft start
- Acceleration Intensity
- Motor Rotation Direction
- Maximum Reverse Speed
- E-brake Intensity
- Maximum Forward Speed
- E-brake Delay Time after Throttle Release
- Throttle Must Be at 0 Before Reapplying Throttle
The Interface for 10301059
To program the motor, two software packages are required: 1. Rewrite and 2. ProClient. Both packages we can send on request.
In the Rewrite software, the default configuration can be loaded and adjusted as desired. Once the adjustments are complete, the new configuration file can be saved to the local PC.
With ProClient, the new configuration file (.bin) can be uploaded to the controller.
- Quinder DC Controller Programming Manual
- Rewrite Manual
- ProClient Manual
Output Cables of the Quinder Controller:
- 48V Power Cable: Composed of 48V + and 48V -. Note: These cables must never be reversed, as this will irreparably damage the Hall sensors.
- Output Cable to Brushless Motor: Includes Motor Phase A, Motor Phase B, Motor Phase C, Motor Hall Sensor +, Motor Hall Sensor -, Motor Hall Sensor Signal A, Motor Hall Sensor Signal B, Speed Signal, Temperature Signal.
- Throttle Cable: Includes RX Protocol, TX Protocol, 48V+, Key, 48V-, Throttle Hall -, Throttle Signal, Throttle +.
- Speaker Cable: Includes Speaker + and Speaker -.
- Programming Cables only for 10301059
- Slow-down Deceleration: Hall +, Hall -, Deceleration Signal (These functions are not available on the Quinder 48V Brushless 8" HUB motor).
- ABS Enable Control Signal: ABS Enable Signal +, ABS Enable Signal - (These functions are not available on the Quinder 48V Brushless 8" HUB motor). only for 10301059
- Fwd/rev switch cable
Quinder Controller Specifications:
- Current Limit: 20A +/- 1A
- Undervoltage: 41V +/- 1V
- Temperature Warning:
- Temp below 90°C – No warning
- Temp between 90°C and 110°C – 0.5 seconds beep, 2 seconds silent
- Temp over 110°C – 1-second beep every other second
- Low Voltage Warning: 0.2-second beep, 1 second silent
- Speed Measurement: By Hall sensor
